Availability: | |
---|---|
Quantity: | |
WDR-8000CS
万达
Product Description
WDR-8000CSMain technical parameters:
itemitem | unit unit | Parameter value Parameter value | Remark remark | |||
Nominal pressing force Nominal pressing force | kN | 80,000 | Adjustable adjustable | |||
Maximum return force of slider Maximum return force of the slider | kN | 2000 | Adjustable adjustable | |||
Maximum working pressure of master cylinder Maximum working pressure of master cylinder | bar | 800 | Adjustable adjustable | |||
Clear spacing of columns (clear spacing of frames) Clear spacing of columns(frame clear spacing) | mm | 1500 | ||||
Moving beam speed and step amount Moving beam speed and step amount | Maximum free travel downward speed (moving beam from the highest position to contacting the workpiece) Maximum down speed in the air(Moving beam from highest position to contact workpiece) | mm/s | 150 | adjustableadjustable
| ||
Maximum pressing speed (work speed) Maximum pressing speed(work rate) | mm/s | 15 | Adjustable adjustable | |||
Single jog step amount Single click step amount | mm/s/times | 0.1-6.0 | Adjustable adjustable | |||
Maximum return speed Maximum return speed | mm/s | 150 | Adjustable adjustable | |||
Maximum stroke of moving beam Maximum travel of moving beam | mm | 600 | adjustableadjustable
| |||
Maximum opening of the press (height toward the mold space) Maximum opening of press(height loading space) | mm | 1,400 | ||||
Upper and lower formwork pad length x width The upper and lower die pads are long wide | mm×mm | 1500*1500 | ||||
Length x width of upper and lower worktables Upper and lower workbench length | mm×mm | 1500*1500 | ||||
Press transverse operating space Horizontal operation space of the press | mm | 1500 | ||||
Moving beam guide method Moving beam guide mode | 1. Rapid cylinder guide; 2.X guide rail guide (2 types used together) 1. Fast cylinder guide; 2.X guide guide (2 kinds together) | |||||
The height of the bottom mold surface from the ground Height of the bottom die surface from the ground | mm | 1. 600mm with foundation; 2. 1710mm without foundation 1. Foundation 600mm; 2. Do not lay foundation 1710mm | ||||
Host height | Height of main engine | mm | About 7000mm About 7000mm
| |||
Maximum temperature of forgings Maximum forging temperature | ℃ | 500 | Requirements of Party A | |||
Whether equipped with mold insulation board Whether to equip mold heat insulation board | 有 Yes | 1 piece each for top and bottom One from top to bottom | ||||
Installed power Installed power | kW | 59.7x6+7.5 | ||||
Overall machine weight Machine weight
| Ton | about 160 About 160 | ||||
Moving beam control method Moving beam control mode | 1. Magnetic scale; 2. Pressure sensor (2 types used together) 1. Magnetic grid ruler; 2. Pressure sensor (2 kinds of combined)
| |||||
Press operation method Press operation mode | Mobile operating table Mobile console | |||||
Main cylinder driving method Master cylinder drive mode | Hydraulic servo drive Hydraulic servo drive | |||||
Is a splash protection system required? Whether a splash protection system is required | need Yes | The machine itself is equipped with a safety door The machine itself is equipped with safety protective doors | ||||
Is there a raster configured? Whether a raster is configured | 有 Yes | 1 set each for front and rear One set before and one set after | ||||
Is a top maintenance platform required? Whether a top maintenance platform is required | need Yes | configured | ||||
Equivalent projected diameter of the loaded area when the press is fully loaded Equivalent projected diameter of the load area of the press at full load | mm | Max 1500 Max. 1500 | Depends on material quality Material quality depends | |||
Press's ability to withstand eccentric load Anti-biased load capacity of the press | Maximum diameter 500 Max diameter 500 | Take the center of the beam plate as the center point of the radius The center of the beam plate is the center point of the radius | ||||
The press column needs to be equipped with a display screen A display screen must be installed on the press column | 有 Yes | On a mobile operating table or electrical box On a mobile console or electrical box | ||||
The press needs to have the function of temporarily storing production data The press must have the function of temporary storage of production data | 有 Yes | Automatic storage function on touch screen The touch screen has automatic storage function | ||||
Liquid working pressure Working liquid pressure | bar | 800/180 | Adjustable adjustable |