After the hydraulic pump of the hydraulic press is used for a certain period of time, the parts of the hydraulic pump will be damaged by wear, resulting in the movement accuracy and working performance of the pump will be reduced, and the oil pressure will not go up, the oil supply will be reduced, the noise will increase, the vibration will increase and other abnormal phenomena. These images are often symptoms of wear or damage to hydraulic pump parts. Once the parts of the hydraulic pump are worn and exceed the allowable deviation, they must be repaired and restored in time, so that the hydraulic pump can get the due accuracy and working performance again. In some cases, skilled operators, through sophisticated repair and assembly, can even improve the performance of the hydraulic pump. Hydraulic pump damage There are a variety of reasons for hydraulic pump damage, but in essence, there are mainly the following two kinds of 1. The wear of hydraulic pump parts, like the parts of any e

Active maintenance emphasizes routine inspection and correction of root causes that would otherwise lead to equipment failure. In the case of hydraulic systems, there are three easily detectable symptoms that give the staff of the hydraulic press manufacturer an early warning of the underlying cause of the condition. These symptoms are abnormal noise, high fluid temperature and slow operation. Abnormal noise Abnormal noise in hydraulic systems is often caused by inflation or cavitation. During aeration, air contaminates the hydraulic oil. The air in the hydraulic fluid makes an amazing tapping or pounding sound when it compresses and decompresses as it passes through the circulatory system. Other symptoms include foamy fluid and erratic actuator movement. Aeration accelerates the degradation of fluids and causes damage to system components through loss of lubrication, overheating and burning of seals. Access to the hydraulic system through the pump inlet. For this reason, it is importa

After a certain period of use of the hydraulic pump of the hydraulic press, the parts of the hydraulic pump will wear and damage, resulting in a decrease in the movement accuracy and working performance of the pump, and various abnormal phenomena such as the inability to push up the oil pressure, the oil supply decreases, the intensification of noise, and the increase in vibration. These imaginations are often a symptom of wear or damage to hydraulic pump parts. Once the parts of the hydraulic pump wear out and exceed the allowable deviation, they must be repaired and restored in time to make the hydraulic pump regain the accuracy and working performance. In some cases, skilled operators can easily improve the working performance of hydraulic pumps through excellent repair and assembly. Causes of hydraulic pump damage There are various reasons for the damage to hydraulic pump, but in its essence, there are mainly two types 1. The wear of wear hydraulic pump parts is the same as that of any equipment, and is the inevitable result of mechanical operation. Under normal use conditions, due to friction and chemical reaction

Active maintenance emphasizes the root causes of routine inspection and correction that would otherwise cause equipment failure. In the case of hydraulic systems, there are three easily detected symptoms that are conditioned to give the hydraulic press manufacturer staff the root cause of early warning. These symptoms are abnormal noise, high fluid temperatures and slow operation. Abnormal noise Anomaly noise in hydraulic systems is often caused by inflation or cavitation. During aeration, the air pollutes the hydraulic oil. Air compresses and decompresses when hydraulic fluid makes a stunning knock or impact sound as it passes through the circulation system. Other symptoms include foamy fluid and unstable actuator movement. Aeration accelerates degradation of fluids and causes damage to the system components through lost lubrication, overheating and combustion of seals. Enter the hydraulic system through the inlet of the pump. For this reason, it is important to ensure that the pump's intake line is in good condition and all clamps and accessories are tight. Flexible air intake tube

Performance characteristics★Computer-optimized structural design, the four-column structure is simple, economical and practical; the frame structure is good rigidity, high accuracy and strong resistance to bias loading. ★The hydraulic control adopts a plug-in basic system, which has reliable operation, long service life, small hydraulic impact, and reduces continuous pipelines and leakage points. ★The electrical system controlled by imported PLc is compact in structure, sensitive, reliable and flexible; the relay control system is reliable in operation, intuitive in action, and convenient in maintenance. ★By selecting the operation panel, not only can the two formal processes be realized in fixed-range and fixed-pressure, but also can realize three process working cycles: padded, padless and ejection. Applicable fields are suitable for various stamping processes such as stretching, bending, forming, punching and blanking, and flanging. They are especially suitable for the following fields: ★Auto parts: body covering parts, brake pads, fuel tanks, chassis, axle shells, bumpers; ★Home use

For four-column hydraulic presses, the viscosity of hydraulic oil has many great impacts on the working state of a machine. So, what impact does the viscosity of hydraulic oil have on the work of the hydraulic system? Viscosity is one of the most important performance indicators of hydraulic oil. Whether it is reasonable or not has a significant impact on the movement stability, working reliability and sensitivity of the hydraulic machine factory system, system efficiency, power consumption, cavitation phenomenon, temperature rise and wear. For example, when the viscosity of hydraulic oil is high, the flow resistance of the hydraulic oil will increase and the flow rate will slow down; and due to friction loss, the consumption of r power will increase; the pressure drop will be added to the valves and pipelines, thereby reducing the efficiency of the system, and the intensification of friction will increase the oil temperature and cause leakage. If the hydraulic viscosity is low, leakage loss will inevitably aggravate, and the oil film between the moving parts will rupture, and the wear of the guide parts will be accelerated. Four-column hydraulic press is in use